Built-ins, columns, wine, drawers, ice
Line answered 24/7

Beverly HillsSub-Zero Specialists
Call (310) 706-2347
Menu

Palisades · Fresh plumbing

Sub-Zero Ice Maker Repair in Pacific Palisades

A rebuilt kitchen means new supply pipes, a new valve behind the cabinetry and an ice maker that has never seen water. A good share of first-month complaints trace back to that new plumbing, not to the machine. Start with the steps below, and when the bin stays bare after that, the comparison further down shows who should come out.

4.8 / 5 · 187 ratings About these reviews

Start-up routine for a new ice maker

Sub-Zero ice makers — the ones built into a freezer compartment and the stand-alone under-counter models — share the same first-week basics.

  1. Confirm the water is really on

    Find the shut-off valve feeding the unit, usually under the sink or in a cabinet beside it, and turn the handle all the way open. Finishing crews often close valves and forget to reopen them.

  2. Flush the new line

    Fresh pipe carries air, flux residue and fine sediment. Where there is a door dispenser, pour off a few glasses, pausing between them, till water comes out clear and without sputtering. With no dispenser, ask the plumber to purge the line into a pail before it is hooked up.

  3. Make sure the filter is seated

    Check that the water filter is installed and clicked fully into place. A filter that is missing, loose or still wrapped in its bag can stop water from reaching the ice maker at all.

  4. Switch the ice maker on

    Many Sub-Zero models ship with ice making turned off in the controls. Find the ice icon on the control panel and check that it is lit.

  5. Let the compartment reach freezing first

    The mold has to be well below freezing before the first harvest. On a brand-new unit, expect to wait about a day before anything drops into the bin.

  6. Throw away the first batches

    Discard the first few bins of ice. They may be cloudy, small, or taste of new plumbing. After that, ice should come out clear and regular.

Direct reply 1/3

Do I need to throw out the first batch of ice?

Yes. The first few bins from a new ice maker or a freshly connected line carry whatever was sitting in the pipes and filter: air, sediment and installation residue. Dump them, let the maker refill, and expect clean, clear cubes after that. The same applies after replacing a water filter.

What a quiet ice maker is trying to say

If the start-up routine is done and the bin is still empty or the ice looks wrong, these patterns point to where the trouble lies.

  1. An empty bin and silence where a fill should be

    Likely Water is not reaching the unit — a closed valve, a kinked line pushed in behind the cabinet, or a problem with the inlet valve

    Repair page
  2. Tiny, hollow or half-formed cubes

    Likely Weak flow: air still trapped in the new line, a partly closed valve, or a filter restricting water

  3. Cloudy, gritty or odd-tasting ice past the first few days

    Likely Sediment in the new plumbing or a filter that was never flushed properly

  4. Water dripping at the back or a wet floor near the cabinet

    Likely A loose compression fitting where the line connects — or, less often, a cracked inlet valve inside the unit

  5. Ice forms but sticks together in a solid clump

    Likely Freezer temperature swinging, or a mechanism that is not ejecting cubes on schedule

  6. An under-counter ice maker floods its own bin

    Likely Its drain path is blocked or was set up without the right slope or pump

Direct reply 2/3

Why is my new ice maker not making ice?

On a new unit the usual reasons are simple: the supply valve is closed, the line is kinked behind the cabinet, the filter is not seated, ice making is switched off in the controls, or the freezer has not been cold long enough. If all five check out and a day passes with nothing, the inlet valve or ice maker needs testing.

Why rebuilt homes see these problems more

The way houses are being finished around the Palisades shapes what goes wrong with a new ice maker.

  • Entirely new supply plumbing

    In a house rebuilt from the slab up, every pipe is new. Air pockets and fine debris are normal at first and they collect at the narrowest passage in the system — the ice maker valve.

  • Water shut off during finishing

    Painters, flooring crews and cabinet installers often shut off the water. If the valve to the refrigerator was closed and never reopened, the ice maker simply waits.

  • Tight panel-ready installations

    Fully integrated units slide into tight millwork. The water line can kink or pinch as the unit is pushed into its niche, leaving the ice maker short of water.

  • Homes standing finished but empty

    When a completed house waits weeks for its owners, the first ice sits in the bin and absorbs odors. Empty and discard it before the family moves in.

  • Hillside water pressure

    Streets climbing toward the canyons can have different pressure from lower blocks near the village. If cubes stay small, pressure at the valve is worth checking along with the filter.

Direct reply 3/3

Is there a Sub-Zero ice maker repair service in Pacific Palisades?

Beverly Hills Sub-Zero Specialists handles Sub-Zero ice makers — the ones built into freezers and the under-counter models — across the Palisades. The line is answered 24/7, and technicians are on the road 8 AM–6 PM, Monday through Sunday. Our $89 call-out is deducted from the final invoice once you say yes to the work; nobody names a part or labor figure until the valve, mold and freezer have been tested.

Installer or technician: who to call

Problems with a brand-new ice maker usually belong to one of two groups. Knowing which one saves a wasted visit.

Call the installer or plumber

  • The shut-off valve is closed or partly closed
  • The water line is kinked, pinched or too short
  • A fitting drips at the connection behind the unit
  • An under-counter ice maker has no proper drain or pump
  • The unit was never connected to water at all

Call a Sub-Zero technician

  • Water reaches the unit but the ice maker never fills
  • The ice maker fills but never ejects cubes
  • The freezer itself is not getting cold enough
  • The inlet valve leaks inside the cabinet
  • Error codes or alarms on the control panel

Our readIf you are unsure, start with the valve and the line — they are quick to check. If water clearly reaches the unit and there is still no ice after a day, call us, and we can also look at the built-in refrigerator in the same visit.

Questions about new ice makers

How frequently does a Sub-Zero ice maker filter need replacing?
Sub-Zero recommends about every six months, or sooner if the filter indicator comes on. In a home with new plumbing, a first change a little earlier than that is reasonable if the ice still looks cloudy. More on the parts that feed an ice maker is on our ice production page.
Is it okay to run the ice maker while trades are still working in the house?
You can, but the ice is likely to taste of new pipes and dust. It is better to keep the ice maker switched off until the plumbing has been flushed and the house is closed up, then follow the start-up routine. The refrigerator drawers on the same circuit are worth a check at the same time.
Where can I find out more before booking?
Phone numbers and booking options sit on the contact page, and the Palisades overview lists all Sub-Zero services in the area. Keep the data-tag model number nearby for the call.

Still no ice after the checks?

Phone at whatever hour suits, or choose a slot online. The $89 trip includes all Sub-Zero equipment at the address, and the charge is folded into the repair invoice when you approve it.

$89 buys the visit, never a per-unit tally; approve the fix and those $89 are deducted from its invoice.